Freshwater Flake Ice Machine for Fishing Industry China
ELECTRIC DRIVE CUTTING TORCH CARRIAGE Gas Cutting Machines,Gas Cutter,Plasma Gas Cutting Machine,Flame Gas Cutting Machine Changzhou Edaweld Trading Company Limited , http://www.edaweld.com
CBFI BF Series flake ice machine maker Introduction:
product model
Model
Ice Making capacity
Capacity of Refrigeraton
Machine Dimension
Weigt of Machine
No.
Ton/24h
KW
W*H*L(mm)
KG
BF500
0.5
3.75
1220*900*1000
160
BF1000
1
8.85
1300*960*1200
210
BF2000
2
17.84
1500*1200*1350
360
BF3000
3
24.15
1800*1250*1500
1000
BF5000
5
35.1
2100*1250*1500
1100
BF6000
6
45.85
2500*2400*2200
1100
BF8000
8
52.7
2100*1250*1500
1300
BF10000
10
76.1
2300*1750*1740
1500
BF15000
15
110.9
3200*2100*2000
3200
BF20000
20
151
3400*2200*2560
4200
BF30000
30
180
3800*2300*2800
5000
BF35000
35
214.2
4500*2300*2800
6000
BF40000
40
226.1
7800*2100*2480
7500
BF50000
50
268.1
5000*2300*3000
10000
BF60000
60
178.4
5500*2300*3200
12000
Feature
-The temperature of ice is lower and it can reach -8 Celsius degree.
- Ice is dry and transparent, good looking shape, non-caked , good mobility and sanitary.
- Ice is flake shape so that it is able to refrigerate products with excellent cooling effect in large area.
-Flake ice has no sharp edges, so it cannot destroy refrigerating product and it is beneficial for storage and
 transportation.
-The thickness of flake ice can be 1mm-2mm .No need to crush and can use at any time.
If you are interested in our flake ice machine maker, pls feel free to contact us. We will reply you in 24hours after getting your inquiry.
*Note*
In your inquiry, pls kindly give me the answer to the questions below:
1. What's your voltage for powering up the machine? Our standard one is 380V/3Phase/50Hz.
2. Do you use fresh water or sea water to make ice?
An improvement over mechanical guides is an electric motor-driven cutting torch carriage. The speed of the motor can be varied allowing the welder to cut to dimensions and to cut at a specific speed. A typical motor driven carriage has four wheels: one driven by a reduction gear, two on swivels (castor style), and one freewheeling. The torch is mounted on the side of the carriage and is adjusted up and down by a gear and rack. The rack is a part of the special torch. The torch also can be tilted for bevel cuts. This machine comes with a straight two-groove track and has a radial bar for use in cutting circles and arcs. A motor-driven cutting torch cutting a circle is shown in figure 4-25. The carriage is equipped with an off-and-on switch, a reversing switch, a clutch, and a speed-adjusting dial that is calibrated in feet per minute.
Figure 4-25.-Electric motor-driven carriage being used to cut a circle in steel plate.
Figure 4-26 shows an electric drive carriage on a straight track being used for plate beveling. The operator must ensure that the electric cord and gas hoses do not become entangled on anything during the cutting operation. The best way to check for hose, electric cord, and torch clearance is to freewheel the carriage the full length of the track by hand.
Figure 4-26.-Electric motor-driven carriage being used on straight track to cut a beveled edge on steel plate.
You will find that the torch carriage is a valuable asset during deployment. This is especially true if your shop is called upon to produce a number of identical parts in quantity. Such an assignment might involve the fabrication of a large supply of handhole covers for runway fixtures, or another assignment might be the production of a large quantity of thick base plates for vertical columns. When using the torch carriage, you should lay the track in a straight line along a line parallel to the edge of the plate you are going to cut. Next, you light the torch and adjust the flame for the metal you are cutting. Move the carriage so the torch flame preheats the edge of the plate and then open the cutting oxygen valve and turn on the carriage motor. The machine begins moving along the track and continues to cut automatically until the end of the cut is reached. When the cut is complete, you should do the following: promptly turn off the cutting oxygen, turn off the current, and extinguish the flame--in that order. The cutting speed depends upon the thickness of the steel being cut